標準號：BS EN 60238-2004+A2-2011
中文標準名稱：愛迪生螺口燈座
英文標準名稱：Edison screw lampholders
標準類型：K74
發布日期：2005/1/20 12:00:00
實施日期：2005/1/20 12:00:00
中國標準分類號：K74
國際標準分類號：29.140.10
引用標準：IEC 60061;IEC 60061-1;IEC 60061-2;IEC 60061-3;IEC 60068-2-20-1979;IEC 60068-2-32-1975;IEC 60068-2-75-1997;IEC 60112-1979;IEC 60227;IEC 60245;IEC 60335-1-2001;IEC 60352-1-1997;IEC 60399;IEC 60417-DB-2002;IEC 60529-1989;IEC 60598;IEC 60598-1;IEC 60664-1-199
適用范圍：This International Standard applies to lampholders with Edison thread E14, E27 and E40,designed for connection to the supply of lamps and semi-luminaires* only.It also applies to switched-lampholders for use in a.c. circuits only, where the working voltagedoes not exceed 250 V r.m.s.This standard also applies to lampholders with Edison thread E5 designed for connection to thesupply mains of series connected lamps, with a working voltage not exceeding 25 V, to be usedindoors, and to lampholders with Edison thread E10 designed for connection to the supplymains of series connected lamps, with a working voltage not exceeding 60 V, to be usedindoors or outdoors. It also applies to lampholders E10 for building-in, for the connection ofsingle lamps to the supply. These lampholders are not intended for retail sale.As far as it reasonably applies, this standard also covers lampholders other than lampholderswith Edison thread designed for connection of series-connected lamps to the supply.NOTE This type of lampholder is for example used in Christmas tree lighting chains.As far as it reasonably applies, this standard also covers adapters.This standard also covers lampholders which are, wholly or partly, integral with a luminaire orintended to be built into appliances. It covers the requirements for the lampholder only. For allother requirements, such as protection against electric shock in the area of the terminals or ofthe lamp cap, the requirements of the relevant appliance standard shall be observed andtested after building into the appropriate equipment, when that equipment is tested according toits own standard. Such lampholders as well as lampholders provided with a snap-on outershell, for use by luminaire manufacturers only, are not for retail sale.This standard applies to lampholders to be used indoors or outdoors in residential as well as inindustrial lighting installations. It also applies to candle lampholders. In locations where specialconditions prevail, as for street lighting, on board ships, in vehicles and in hazardous locations,e.g. where explosions are liable to occur, special constructions may be required.NOTE 1 This standard does not apply to three-light lampholders E26d.NOTE 2 This standard is based on the following data relative to lamps for general lighting service:– caps E14 are used for lamps with a current not exceeding 2 A;– caps E27 are used for lamps with a current not exceeding 4 A;– caps E40 are used for lamps with a current not exceeding 16 A.NOTE 3 If the nominal voltage of the supply does not exceed 130 V, the maximum current for caps E40 is 32 A(see 4.5 and 5.3).NOTE 4 Where lampholders are used in luminaires, their maximum operating temperatures are specified inIEC 60598.