標準號：BS EN 13598-2-2009
中文標準名稱：無壓力地下排水和排污用塑料管道系統.未增塑聚氯乙烯(PVC-U),聚丙烯(PP)和聚乙烯(PE).第2部分:交通范圍和地下設施中檢修孔和檢查室用規范
英文標準名稱：Plastics piping systems for nonpressure underground drainage and sewerage — Unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 2: Specifications for manholes and inspection chambers in traffic areas and dee
標準類型：Q81
發布日期：2009/2/28 12:00:00
實施日期：2009/2/28 12:00:00
中國標準分類號：Q81
國際標準分類號：93.030
引用標準：EN 124-1994;EN 476-1997;EN 681-1-2002;EN 681-2-2000;EN 728-1997;EN 681-3-2002;EN 681-4-2000;EN 744-1995;EN 922-1994;EN 1277-2003;EN 1401-1;EN 1852-1;EN 12061;EN 12666-1;EN 13101-2002;EN 13476-1;EN 13476-2;EN 13476-3;EN 14396-2004;CEN/TS 14541;EN 14758-1;E
適用范圍：This European Standard specifies the definitions and requirements for buried manholes andinspection chambers installed to a maximum depth of 6 m from ground level to the invert of the mainchamber and manufactured from unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP),polypropylene with mineral modifier (PP-MD) or polyethylene (PE). These products are intended foruse in pedestrian or vehicular traffic areas and underground installations conforming to the generalrequirements given in EN 476 and are used outside the building structure (application area code “U”).They are therefore marked accordingly with a “U”. Such products are also deemed to meet therequirements of EN 13598-1 for application area U without the need for further testing. If additionallymarked application area D then these products must additionally be tested to show compliance to theelevated temperature cycling requirement of Clause 10 of EN 13598-1.This European Standard is only applicable to those chamber / manhole items where the manufacturerhas clearly stated in the documentation how the components shall be assembled to create a completemanhole or inspection chamber.The inspection chambers covered by this European Standard comprise the following:? inspection chambers providing access to the drainage or sewerage system by means ofinspection and cleaning equipment.? chambers, designated as manholes providing man access to the drainage or sewerage system.The inspection chamber / manhole can be manufactured by various methods e.g. injection moulding,rotational moulding, low-pressure moulding or fabricated from components made in accordance withother standards.The jointing of components can be achieved using:? elastomeric ring seal joints;? adhesive joints for PVC-U;? welded joints for PVC-U, PP and PE;? extrusion welding;? mechanical jointing.NOTE Both manholes and inspection chambers can be site assembled from different components, but canalso be manufactured as a single unit. In either case, the following functional parts can be recognized:a) base (always present)In case of a one-piece chamber or manhole, the base part ends at a distance of 300 mmmeasured from the top of the main channel;b) riser (depth dependent);c) telescopic part (design dependent);d) cone (dependent on the design of near surface components and their recommended installation);e) other near surface components